Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Alternatives for the asphalt Coating in Alabaster, Alabama


Tar And Chip Paving installed on an unstable surface can quickly lead to difficulties. There are 3 main choices for the basic setup:

  1. Paving Over Existing Driveway: If your current driveway is in good condition rather than showing severe cracks or crumbling, hot asphalt mix can be laid directly over your driveway. One facet is elevation: make sure fences, garage floors, and other constructions are not jeopardized by the greater degree of this surface.
  2. Eliminate old driveway, peg to the floor: The existing driveway is totally removed (or you may not have a driveway yet) and 4 to 6 inches of warm paving stone is put directly on the ground.
  3. Remove the old driveway and fasten it to a solid surface. This is actually the preferred method. An aggregated stone flooring partly replaces part of this hot asphalt mix.

The more asphalt you operate, the more leeway you have. For instance, at 40 F, the crews just have 16 minutes to work on 1 1/2 inch thick asphalt. As the asphalt depth increases by 3 inches, the workability time also increases: 46 minutes. In general, for lean asphalt programs (approximately 1.5 cm), you need to wait until temperatures are 21 ° C or even higher. Between 50 and 60 F, then you ought to consult with your contractor. The hot mix remains practical in this period of time, but the time is constrained.

How much can an Tar And Chip Paving cost in Alabaster?

Consider the weather vagaries of the climate when choosing the quality of asphalt. The significant temperature variations we experience cause considerable damage to asphalt work.

In addition, it will be good to tell the contractor if you have a recreational vehicle or a van. He will have to accommodate the asphalt mixture so as to be more immune to the weight of heavy vehicles.

The advantages of Tar And Chip Paving

  • Smooth end;
  • non invasive
  • easy to Keep
  • watertightness ensured
  • withstands the rigors of this Quebec climate very well (provided it has been set up );
  • prevents the growth of moss;

It'll cost you between $ 3 and $11 per square foot; the price varies depending on the quality of the asphalt used and the paving contractor.

To get a sustainable Tar And Chip Paving

The existence of an asphalt paver can be up to 20 decades, when the very best states are satisfied. We're referring to a professional paving builder, a great quality of asphalt and also an optimal asphalt laying technique.

Tar And Chip Paving in Alabaster: cost, quality of work and lifespan


The durability of residential asphalt paving largely depends on the standard of the laying. Really, the major causes of deformation or ripping of an asphalt layer are the absence of compaction and a thin foundation. However, the maintenance of the asphalt sidewalk is also a determining factor in its longevity. That is to say, you'll need to seal your drive once in ten decades, at a minimum, so as to keep its great state.


We advise you to inform your asphalting contractor in case you choose to get your driveway asphalt in order to sell your property. It might not be essential to pay top dollar for placing asphalt , in this case.

Tar And Chip Paving laying: cost and contract

The choice of the asphalt laying builder is indispensable. In order not to have unpleasant surprises, then you'll have to choose it carefully.

Our ensures and Tar And Chip Paving work

Guarantee that the paving contractor has liability insurance coverage. A visit to the web site of the Office for Consumer Protection (OPC) will allow you to confirm whether an entrepreneur has ever been the subject of complaints.

These details should be included in the arrangement:

- date of start and finish of the work;

- proof of insurance;

- technical particulars;

- RBQ certification number.

You should be aware that a paving builder can't require that you make a down payment before work has begun. However, you need to agree to the payment provisions and make sure it's about the contract.

A strong base for Tar And Chip Paving- Alabaster

Before redoing the asphalt drive to your new residence by a builder, or acquiring some fundamental knowledge is vital to guarantee that the job is done. Know first that the lack of compaction and the inadequate thickness of the foundation are the two chief sources for the deformation or tearing of a coating of asphalt. If it's a new driveway, it has to first be excavated to make room for a coating of crushed stone of adequate thickness. A geotextile membrane will be placed under the granular backfill if the dirt turns out to be somewhat loamy (clayey). If you have a new home, it is best to wait 6 to 12 months before paving your drive, to enable the soil to settle . In the event of a repair of the entry, a simple replacement of the asphalt coating can be considered in the event the contractor believes that the existing foundation is sufficient. In both cases, base redone or foundation maintained, the duration of its guarantee has to be exactly the same.

Tar And Chip Paving Alabaster Alabama

The weather conditions in our lovely state may have a disastrous impact in an asphalt drive, thus the importance of including a slope having a minimum slope of 2%. This will enable water to drain into the street and minimize the risk of heaving or cracking. This significant detail has to be taken into account when excavating and preserved during backfilling.

In case you've got a van or recreational vehicle, notify the contractor before the onset of the job: he will have the ability to supply materials accordingly. Some asphalt mixtures produce an asphalt which is more immune to heavy-duty vehicles.

The asphalt coating should have an initial thickness of 6.35 to 7.6 cm (2.5 to 3 in) in order to accomplish a thickness of 5 cm (2 ) after being compacted. For optimum stability, the foundation should extend over the surface to be paved by roughly thirty centimeters (a dozen inches) on each side. Also mention that the setup of side supports around the base is a fantastic way to prevent possible cracks and that asphalting done in chilly weather is going to be of inferior quality. It is therefore better to await the sunny days to go back before beginning work.

To avoid unpleasant surprises, then select your contractor diligently and be certain the name and address of his business are composed on the contract. The beginning and finish dates of this work, in addition to evidence of the builder's liability insurance and the technical details of the project to be completed, should also be included. No contractor should require a down payment before work begins. To avoid the inconvenience that could lead to unforeseen costs, take a look at the Tar And Chip PavingAlabaster site. You may thus have all the resources in hand to successfully complete your asphalt paving project.

Tar And Chip Paving Alabaster - Best Alabama at Alabama!

For caliber asphalting work , phone on Tar And Chip Paving, Alabaster specialist team. We've got more than twenty decades of experience in asphalt laying, resurfacing, maintenance and repair. Confirm our Business section to find out the regions served.

Snow Removal Alabaster | Asphalt Alabaster
Home >> alabama/alabaster >> tar and chip paving
Share this...