Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Alternatives for the asphalt Coating in Anniston, Alabama


Tar And Chip Paving installed on an unstable surface could quickly lead to problems. There are three Chief options for the basic installation:

  1. Paving Over Existing Driveway: If your current driveway is in good shape rather than showing severe cracks or crumbling, hot asphalt mixture can be placed directly within your driveway. 1 aspect is height: make certain fences, garage floors, and other constructions are not compromised by the greater level of the surface.
  2. Remove old driveway, counter into the floor: The existing driveway is totally removed (or you might not have a driveway yet) and 4 to 6 inches of hot paving stone is placed right on the ground.
  3. Remove the old driveway and secure it into a solid surface. This is actually the preferred method. An aggregated stone floor partially replaces part of the hot asphalt mixture.

Our Services:

The best time to install Tar And Chip Paving from Anniston

The more asphalt you operate, the more leeway you might have. By way of example, at 40 F, the crews only have 16 minutes to operate on 1 1/2 inch thick asphalt. Generally, for thin asphalt programs (approximately 1.5 cm), you need to wait until temperatures are 21 ° C or higher. Between 50 and 60 F, then you'll need to speak to your contractor. The hot mix is ​​still functional in this period, however, the time is constrained.

How much does an Tar And Chip Paving cost in Anniston?

Take into account the weather vagaries of our climate when choosing the quality of asphalt. The significant temperature variations that we experience cause appreciable damage to asphalt perform.

In addition, it will be useful to distinguish the contractor if you own a recreational vehicle or even a van. He might need to adapt the asphalt mix so as to be more resistant to the weight of heavy vehicles.

The Benefits of Tar And Chip Paving

A driveway paved with asphalt has several advantages:

It'll cost you between $ 3 and $11 per square foot; the price varies depending on the characteristic of the asphalt used along with the paving contractor.

For a sustainable Tar And Chip Paving

The life of an asphalt paver may be up to 20 years, when the best states are satisfied. We're talking about a professional paving builder, a good grade of asphalt as well as also an optimal asphalt laying technique.

Tar And Chip Paving in Anniston: price, quality of work and lifespan


The longevity of residential asphalt paving chiefly depends upon the quality of the placing. Really, the significant causes of deformation or ripping of an asphalt coating are the absence of compaction and a lean base. On the other hand, the maintenance of the asphalt sidewalk is also a deciding factor in its own longevity. That's to say, you'll have to seal your driveway once in ten decades, at a minimum, so as to maintain its good state.


We suggest that you inform your asphalting contractor in case you decide to have your driveway asphalt in order to offer your property. It might not be necessary to pay top dollar for laying asphalt , in this circumstance.

Tar And Chip Paving placing: cost and contract

The option of the asphalt laying contractor is essential. In order to not have unpleasant surprises, you will need to choose it carefully.

Our guarantees and Tar And Chip Paving work

Guarantee that the paving contractor has liability insurance coverage. A visit to the web site of the Office for Consumer Protection (OPC) will allow you to confirm whether an entrepreneur has been the subject of complaints.

These details should be included in the arrangement:

- date of start and finish of the job;

- evidence of insurance;

- technical particulars;

- RBQ certification number.

You should be aware that a paving builder can't require that you make a deposit before work has begun. However, you should agree on the payment provisions and be sure it is on the contract.

Prior to estimating the asphalt drive to your new home by a builder, or obtaining some fundamental knowledge is vital to make sure the job is well done. Know first that the absence of compaction and the inadequate depth of the foundation are the two main sources for the deformation or tearing of a layer of asphalt. When it's a new driveway, then it has to first be excavated to make room for a coating of crushed stone of adequate thickness. A geotextile membrane will be placed beneath the granular backfill if the soil turns out to be very loamy (clayey). If you own a new home, it's best to wait 6 to 12 months before paving your driveway, to allow the soil to settle naturally. In the case of a fix of the entrance, an easy replacement of the asphalt layer can be considered if the contractor believes that the existing base is sufficient. In both scenarios, foundation redone or foundation preserved, the whole period of its warranty must be the same.

Tar And Chip Paving Anniston Alabama

The weather conditions in our lovely state can have a devastating effect in an asphalt driveway, thus the significance of adding a slope having a minimum slope of 2%. This will enable water to drain into the road and decrease the danger of heaving or cracking. This important detail must be taken into consideration when excavating and maintained during backfilling.

If you have a van or recreational vehicle, notify the builder before the start of the job: he is going to have the ability to supply materials so. Some asphalt mixtures produce an asphalt which is more immune to heavy-duty vehicles.

The asphalt coating should have an initial thickness of 6.35 to 7.6 cm (2.5 to 3 in) so as to accomplish a thickness of 5 cm (2 ) after being compacted. For optimum stability, the base should extend across the surface to be paved by about thirty centimeters (a dozen inches) on each side. Also note that the installation of side supports around the base is a fantastic way to prevent potential cracks and that asphalting done in chilly weather will be of poor quality. It's therefore far better to wait for the bright days to return before starting work.

A definite contract with your builder in Anniston

To avoid unpleasant surprises, then choose your contractor diligently and make sure that the name and address of his business are composed on the contract. The start and finish dates of the work, as well as evidence of this builder's liability insurance and the technical specifics of this project to be completed, should also be included. No contractor should need a deposit before work begins. To prevent the inconvenience that could cause unforeseen costs, visit the Tar And Chip PavingAnniston website. You will thus have all the resources in hand to successfully finish your asphalt paving project.

Tar And Chip Paving Anniston - Greatest Alabama in Alabama!

For caliber asphalting perform , call on Tar And Chip Paving, Anniston specialist team. Consult our Business section to find out the regions served.

Snow Removal Anniston | Asphalt Anniston
Home >> alabama/anniston >> tar and chip paving
Share this...