Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Options for the asphalt surface in Atmore, Alabama


Tar And Chip Paving installed on an unstable surface could quickly lead to problems. There are three Chief options for the Simple installation:

  1. Paving Over Existing Driveway: If your current driveway is in good condition rather than revealing severe cracks or crumbling, hot asphalt mix can be laid directly over your driveway. One facet is height: make certain fences, garage flooring, and other structures are not jeopardized by the higher level of this new surface.
  2. Remove old driveway, peg to the ground: The existing driveway is totally eliminated (or you might not have a driveway yet) and 4 to 6 inches of warm paving stone is put directly on the ground.
  3. Eliminate the old driveway and fasten it into a good surface. This is actually the preferred method. An aggregated stone flooring partially replaces part of this hot asphalt mixture. Typically 6 to 8 inches of aggregate goes under 3 inches of asphalt.

The more asphalt you work, the more leeway you might have. For instance, in 40 F, the crews only have 16 minutes to operate on 1 1/2 inch thick asphalt. In general, for thin asphalt applications (about 1.5 cm), you need to wait until temperatures are 21 ° C or even higher. Between 50 and 60 F, then you'll need to speak to your contractor. The hot mix remains functional during this period, but the time is limited.

How much does an Tar And Chip Paving cost in Atmore?

Consider the weather vagaries of our climate when deciding upon the standard of asphalt. The significant temperature variations we experience cause considerable damage to asphalt perform.

Furthermore, it will be good to distinguish the contractor if you have a recreational vehicle or even a van. He might have to accommodate the asphalt mixture so as to be more resistant to the burden of heavy vehicles.

The Benefits of Tar And Chip Paving

A driveway paved with asphalt has several benefits:

It will cost you between $ 3 and $11 per square foot; the price varies depending on the characteristic of the asphalt employed along with the paving contractor.

For a sustainable Tar And Chip Paving

The existence of an asphalt paver may be up to 20 decades, when the best states are met. We're referring to a professional paving contractor, a good quality of asphalt as well as an optimal asphalt laying technique.

Tar And Chip Paving in Atmore: cost, quality of work and lifespan


The durability of residential asphalt paving largely is dependent on the quality of the laying. Really, the major causes of deformation or tearing of an asphalt layer are the lack of compaction and a thin foundation. However, the maintenance of the asphalt sidewalk can be a deciding factor in its longevity. That's to say, you'll need to seal your drive once in 10 decades, at a minimum, so as to keep its great condition.


We advise you to notify your asphalting contractor if you decide to have your driveway asphalt in order to sell your property. It might not be essential to pay top dollar for placing asphalt , in such a case.

Tar And Chip Paving laying: cost and contract

The choice of the asphalt laying contractor is indispensable. In order not to have unpleasant surprises, you will have to choose it carefully.

Our ensures and Tar And Chip Paving work

Make sure the paving contractor has liability insurance coverage. A visit to the web site of the Office for Consumer Protection (OPC) will allow you to confirm whether an entrepreneur has been the subject of complaints.

The following details must be included in the contract:

- date of beginning and finish of the job;

- proof of insurance;

- technical details;

- RBQ certification number.

You ought to know that a paving builder cannot demand you to make a deposit before work has begun. However, you need to agree on the payment terms and be sure it is on the contract.

Prior to estimating the asphalt driveway to your new home by a contractor, or obtaining some basic knowledge is vital to guarantee that the job is done. Know first that the lack of compaction and the inadequate depth of the base are the two main causes of the deformation or ripping of a layer of asphalt. If it is a new driveway, then it must first be excavated to make room for a layer of crushed stone of adequate depth. A geotextile membrane is going to be set under the granular backfill if the soil proves to be very loamy (clayey). If you have a new house, it's best to wait 6 to 12 months before paving your driveway, to enable the soil to settle . In the case of a fix of this entrance, an easy replacement of the asphalt layer can be considered in the event the contractor considers that the present foundation is adequate. In both cases, base redone or base maintained, the whole period of its guarantee has to be the same.

Tar And Chip Paving Atmore Alabama

The weather conditions in our beautiful province may have a disastrous impact in an asphalt driveway, thus the importance of adding a slope having a minimum slope of 2%. This will allow water to drain into the road and decrease the risk of heaving or cracking. This important detail has to be taken into account when excavating and preserved during backfilling.

In case you have a van or recreational vehicle, notify the contractor prior to the start of the job: he is going to have the ability to supply materials so. Some asphalt combinations produce an asphalt that is more immune to heavy duty vehicles.

The asphalt layer should have an initial thickness of 6.35 to 7.6 cm (2.5 to 3 ) so as to accomplish a thickness of 5 cm (2 in) after being compacted. For optimum stability, the foundation should extend across the surface to be paved by about thirty centimeters (a couple inches) on each side. Also note that the installation of unwanted supports around the foundation is a fantastic way to prevent potential cracks and this asphalting done in chilly weather will be of poor quality. It is therefore better to wait for the sunny days to go back before beginning work.

To avoid unpleasant surprises, select your contractor diligently and be certain that the name and address of the company are written on the contract. The beginning and end dates of this work, as well as evidence of the builder's liability insurance and the technical details of this project to be carried out, should also be included. No contractor should require a down payment before work starts. To prevent the inconvenience that could lead to unforeseen costs, take a look at the Tar And Chip PavingAtmore website. You may thus have the resources in hand to successfully complete your asphalt paving project.

Tar And Chip Paving Atmore - Greatest Alabama at Alabama!

For caliber asphalting perform , phone on Tar And Chip Paving, Atmore specialist team. We've got more than 20 decades of expertise in asphalt laying, resurfacing, maintenance and repair. Confirm our Business department to figure out the regions served.

Snow Removal Atmore | Asphalt Atmore
Home >> alabama/atmore >> tar and chip paving
Share this...