Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Options for the asphalt surface in Auburn, Alabama


Tar And Chip Paving installed on an unstable surface could quickly lead to difficulties. There are three Chief choices for the Simple installation:

  1. Paving Over Existing Driveway: If your current driveway is in good shape and not showing severe fractures or crumbling, hot asphalt mix can be placed directly within your driveway. One facet is elevation: make sure fences, garage floors, and other structures aren't compromised by the greater level of this new surface.
  2. Remove old driveway, peg to the floor: The existing driveway is totally removed (or you might not have a driveway nonetheless ) and 4 to 6 inches of warm paving stone is placed right on the ground.
  3. Eliminate the old driveway and fasten it to a good surface. This is the preferred method. An aggregated stone flooring partially replaces part of this hot asphalt mixture. Typically 6 to 8 inches of limestone extends under 3 inches of asphalt.

The more asphalt you work, the more leeway you might have. For instance, at 40 F, the crews just have 16 minutes to operate on 1 1/2 inch thick asphalt. As the asphalt depth increases by 3 inches, the workability time also increases: 46 minutes. In general, for thin asphalt applications (approximately 1.5 cm), you need to wait until temperatures are 21 ° C or higher. Between 50 and 60 F, you ought to speak to your contractor. The hot mix remains functional during this period, but the time is limited.

How much can an Tar And Chip Paving price in Auburn?

Consider the weather vagaries of our climate when deciding upon the standard of asphalt. The significant temperature variations that we experience cause considerable damage to asphalt work.

Furthermore, it'll be good to tell the contractor if you own a recreational vehicle or even a van. He might need to accommodate the asphalt mixture in order to be more resistant to the weight of heavy vehicles.

The Benefits of Tar And Chip Paving

  • Smooth finish;
  • non-slip
  • easy to Keep
  • watertightness ensured
  • withstands the rigors of this Quebec climate quite well (provided it's been installed optimally);
  • prevents the growth of moss;

It'll cost you between $ 3 and $11 per square foot; the price varies depending on the characteristic of the asphalt used along with the paving contractor.

To get a sustainable Tar And Chip Paving

The existence of an asphalt paver may be up to 20 decades, when the very best conditions are satisfied. We're talking about a professional paving builder, a great quality of asphalt as well as also an optimal asphalt laying technique.

Tar And Chip Paving in Auburn: cost, quality of work and lifespan


The durability of residential asphalt paving chiefly depends upon the standard of the laying. Indeed, the major causes of deformation or tearing of an asphalt layer are the lack of compaction plus a lean base. On the other hand, the upkeep of the asphalt sidewalk is also a deciding factor in its own longevity. That is to say, you will have to seal your drive once in ten decades, at a minimum, in order to maintain its great state.


We advise you to notify your asphalting builder in case you decide to get your driveway asphalt so as to offer your property. It might not be essential to pay top dollar for placing asphalt , in this circumstance.

Tar And Chip Paving laying: cost and contract

The choice of the asphalt laying builder is essential. In order not to have unpleasant surprises, then you'll need to select it carefully.

Make sure the paving contractor has liability insurance coverage. A visit to the website of the Office for Consumer Protection (OPC) will allow you to verify whether an entrepreneur has ever become the subject of complaints.

These details must be included in the arrangement:

- date of beginning and end of the work;

- proof of insurance;

- technical details;

- RBQ certification number.

You ought to be aware that a paving contractor cannot demand that you make a down payment before work has begun. However, you should agree on the payment provisions and make sure it's about the contract.

Before redoing the asphalt drive to your new residence by a builder, or acquiring some basic knowledge is imperative to make sure the job is done. Know first that the lack of compaction and the inadequate thickness of the foundation are the two main causes of the deformation or ripping of a layer of asphalt. When it's a new driveway, it must first be excavated to make room for a layer of crushed stone of sufficient thickness. A geotextile membrane will be set under the granular backfill if the soil turns out to be very loamy (clayey). If you have a new house, it is best to wait for 6 to 12 months prior to paving your driveway, to allow the soil to settle naturally. In the event of a repair of this entrance, a simple replacement of the asphalt layer can be considered in the event the contractor believes that the existing base is sufficient. In both scenarios, foundation redone or base preserved, the duration of its warranty must be exactly the same.

Tar And Chip Paving Auburn Alabama

The weather conditions in our beautiful province may have a disastrous impact in an asphalt driveway, hence the significance of adding a slope with a minimum slope of 2%. This will enable water to drain to the street and decrease the risk of heaving or cracking. This significant detail must be taken into consideration when excavating and preserved during backfilling.

In case you have a van or recreational vehicle, notify the contractor before the start of the work: he is going to have the ability to supply materials accordingly. Some asphalt combinations produce an asphalt that is more resistant to heavy duty vehicles.

The asphalt layer should have an initial thickness of 6.35 to 7.6 cm (2.5 to 3 ) in order to accomplish a thickness of 5 cm (2 in) after being compacted. For optimum stability, the foundation should extend over the surface to be paved by roughly thirty centimeters (a couple inches) on each side. Also mention that the installation of unwanted supports around the base is a good method to prevent potential cracks and that asphalting done in cold weather will be of poor quality. It is therefore better to await the bright days to return before beginning work.

A definite contract with your builder in Auburn

To avoid unpleasant surprises, then select your contractor diligently and make sure the name and address of his business are composed on the contract. The start and finish dates of this work, as well as proof of the contractor's liability insurance and the technical details of this job to be carried out, should also be included. No contractor should need a down payment before work begins. To avoid the inconvenience that might cause unforeseen costs, take a look at the Tar And Chip PavingAuburn site. You may thus have the tools in hand to successfully complete your asphalt paving project.

Tar And Chip Paving Auburn - Best Alabama at Alabama!

For quality asphalting perform , call on Tar And Chip Paving, Auburn professional team. Consult our Company section to find out the regions served.

Snow Removal Auburn | Asphalt Auburn
Home >> alabama/auburn >> tar and chip paving
Share this...