Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Alternatives for the asphalt Coating in Foley, Alabama


Tar And Chip Paving installed on an unstable surface could quickly lead to difficulties. There are 3 main choices for the basic setup:

  1. Paving Over Existing Driveway: If your current driveway is in good condition and not showing severe cracks or crumbling, hot asphalt mix can be placed directly within your driveway. 1 aspect is elevation: make certain fences, garage flooring, and other structures are not jeopardized by the higher level of the surface.
  2. Remove old driveway, counter into the floor: The present driveway is totally eliminated (or you may not have a driveway yet) and 4 to 6 inches of hot paving stone is placed directly on the ground.
  3. Eliminate the old driveway and secure it into a solid surface. This is the preferred method. An aggregated stone floor partially replaces part of the hot asphalt mixture. Typically 6 to 8 inches of limestone goes under 3 inches of asphalt.

The more asphalt you work, the more leeway you might have. By way of instance, in 40 F, the crews only have 16 minutes to operate on 1 1/2 inch thick asphalt. As the asphalt depth increases by 3 inches, the workability time also raises: 46 minutes. Generally, for lean asphalt applications (about 1.5 cm), you should wait until temperatures are 21 ° C or higher. Between 50 and 60 F, you ought to consult with your contractor. The hot mix remains functional during this period, however, the time is constrained.

How much can an Tar And Chip Paving price in Foley?

Consider the weather vagaries of the climate when choosing the quality of asphalt. The substantial temperature variations we experience cause considerable damage to asphalt work.

In addition, it'll be good to tell the contractor if you have a recreational vehicle or even a van. He might need to adapt the asphalt mix in order to be more immune to the burden of heavy vehicles.

The advantages of Tar And Chip Paving

  • Smooth finish;
  • non invasive
  • easy to Keep
  • watertightness guaranteed
  • withstands the rigors of the Quebec climate quite well (provided it has been installed );
  • prevents the growth of moss;

It'll cost you between $ 3 and $11 per square foot; the price fluctuates based on the quality of the asphalt used along with the paving contractor.

To get a sustainable Tar And Chip Paving

The life of an asphalt paver can be around 20 years, when the very best conditions are satisfied. We are talking about a professional paving builder, a great grade of asphalt as well as an optimal asphalt laying technique.

Tar And Chip Paving in Foley: price, quality of work and lifespan


The longevity of residential asphalt paving largely is dependent upon the standard of the placing. Really, the significant causes of deformation or tearing of an asphalt layer are the lack of compaction and a lean base. However, the maintenance of the asphalt sidewalk can be a determining factor in its longevity. That's to say, you will have to seal your drive once in ten years, at a minimum, in order to maintain its great condition.


We suggest that you inform your asphalting builder if you decide to have your driveway asphalt so as to offer your property. It might not be necessary to pay top dollar for placing asphalt , in such a circumstance.

Tar And Chip Paving placing: cost and contract

The choice of the asphalt laying contractor is essential. In order to not have unpleasant surprises, you will need to select it carefully.

Our guarantees and Tar And Chip Paving work

Guarantee that the paving contractor has liability insurance. A trip to the web site of the Office for Consumer Protection (OPC) will allow you to verify whether an entrepreneur has become the subject of complaints.

These details must be included in the arrangement:

- date of beginning and end of the work;

- evidence of insurance;

- technical particulars;

- RBQ certification number.

You should be aware that a paving builder can't demand you to make a down payment before work has begun. But you should agree to the payment terms and make sure it's on the contract.

Prior to estimating the asphalt driveway to your new residence by a builder, or obtaining some fundamental knowledge is imperative to make sure the job is done. Know first that the lack of compaction and the inadequate thickness of the base are the two main causes of the deformation or ripping of a layer of asphalt. If it is a new driveway, it has to first be excavated to make room for a layer of crushed stone of sufficient thickness. A geotextile membrane will be set under the granular backfill if the soil proves to be somewhat loamy (clayey). If you have a new house, it is best to wait 6 to 12 months prior to paving your drive, to allow the dirt to settle . In the event of a repair of this entry, an easy replacement of the asphalt layer can be considered in the event the contractor believes that the present foundation is adequate. In both cases, base redone or foundation preserved, the whole period of its warranty has to be the same.

Tar And Chip Paving Foley Alabama

The weather conditions in our beautiful province can have a disastrous impact on an asphalt drive, thus the significance of including a slope with a minimum slope of 2%. This will enable water to drain to the road and minimize the risk of heaving or cracking. This significant detail has to be taken into account when excavating and maintained during backfilling.

If you have a van or recreational vehicle, notify the builder prior to the start of the job: he is going to be able to provide materials so. Some asphalt mixtures produce an asphalt which is more immune to heavy-duty vehicles.

The asphalt coating should have an initial thickness of 6.35 to 7.6 cm (2.5 to 3 ) in order to accomplish a thickness of 5 cm (2 ) after being compacted. For optimal stability, the base should extend over the surface to be paved by roughly thirty centimeters (a dozen inches) on each side. Also mention that the installation of side supports around the base is a good way to avoid possible cracks and this asphalting done in cold weather is going to be of inferior quality. It is therefore better to wait for the bright days to return before beginning work.

A definite contract with your contractor in Foley

To avoid unpleasant surprises, then choose your contractor and be certain the title and address of the company are written about the contract. The beginning and finish dates of the job, as well as proof of this builder's liability insurance and the technical specifics of this job to be completed, should also be included. No contractor should need a down payment before work begins. To avoid the inconvenience that could lead to unforeseen costs, take a look at the Tar And Chip PavingFoley website. You may thus have the tools in hand to successfully complete your asphalt paving project.

Tar And Chip Paving Foley - Best Alabama at Alabama!

For quality asphalting work , call on Tar And Chip Paving, Foley specialist team. We've got over twenty decades of experience in asphalt laying, resurfacing, maintenance and repair. Confirm our Company department to figure out the regions served.

Snow Removal Foley | Asphalt Foley
Home >> alabama/foley >> tar and chip paving
Share this...