Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Alternatives for the asphalt Coating in Pell City, Alabama


Tar And Chip Paving installed in an unstable surface could quickly lead to problems. There are 3 Chief choices for the Simple setup:

  1. Paving Over Existing Driveway: If your current driveway is in good shape rather than showing severe cracks or crumbling, hot asphalt mixture can be placed directly within your driveway. 1 facet is elevation: make sure fences, garage floors, and other structures aren't compromised by the greater degree of the surface.
  2. Eliminate old driveway, counter into the floor: The present driveway is totally eliminated (or you may not have a driveway yet) and 4 to 6 inches of hot paving stone is placed right on the ground.
  3. Eliminate the old driveway and fasten it to a solid surface. This is the preferred method. An aggregated stone flooring partially replaces part of this hot asphalt mix.

The more asphalt you work, the more leeway you might have. For instance, at 40 F, the crews only have 16 minutes to operate on 1 1/2 inch thick asphalt. In general, for thin asphalt programs (approximately 1.5 cm), you should wait until temperatures are 21 ° C or higher. Between 50 and 60 F, then you ought to speak to your contractor. The hot mix is ​​still functional during this period of time, but the time is constrained.

How much can an Tar And Chip Paving price in Pell City?

Consider the weather vagaries of our climate when deciding upon the standard of asphalt. The significant temperature variations we experience cause considerable damage to asphalt work.

Furthermore, it will be good to tell the contractor should you own a recreational vehicle or even a van. He might have to adapt the asphalt mix in order to be more resistant to the burden of heavy vehicles.

The Benefits of Tar And Chip Paving

  • Smooth end;
  • non invasive
  • easy to Keep
  • watertightness guaranteed
  • withstands the rigors of this Quebec climate very well (provided it's been installed optimally);
  • prevents the growth of moss;

It'll cost you between $ 3 and $11 per square foot; the price varies depending on the quality of the asphalt used along with the paving contractor.

To get a sustainable Tar And Chip Paving

The existence of an asphalt paver may be around 20 decades, when the very best states are met. We are talking about a professional paving contractor, a good quality of asphalt as well as an optimal asphalt laying technique.


The durability of residential asphalt paving chiefly depends on the standard of the placing. Really, the significant causes of deformation or tearing of an asphalt coating are the lack of compaction plus a lean base. However, the maintenance of the asphalt pavement is also a deciding factor in its own longevity. That's to say, you'll need to seal your drive once in ten years, at a minimum, in order to maintain its good state.


We suggest that you inform your asphalting builder if you decide to have your driveway asphalt in order to offer your property. It might not be necessary to pay top dollar for placing asphalt , in this case.

Tar And Chip Paving placing: price and contract

The option of the asphalt laying contractor is essential. In order to not have unpleasant surprises, you'll have to choose it carefully.

Our guarantees and Tar And Chip Paving work

Make sure the paving contractor has liability insurance coverage. A trip to the web site of the Office for Consumer Protection (OPC) will make it possible for you to verify whether an entrepreneur has become the subject of complaints.

The following details should be included in the arrangement:

- date of beginning and finish of the work;

- proof of insurance;

- technical particulars;

- RBQ accreditation number.

You ought to know that a paving contractor cannot demand that you make a down payment before work has started. However, you need to agree on the payment provisions and be sure it is about the contract.

A strong base for Tar And Chip Paving- Pell City

Before redoing the asphalt driveway to your new home by a contractor, or obtaining some basic knowledge is vital to guarantee that the job is done. Know first that the absence of compaction and the inadequate depth of the foundation are the two main sources for the deformation or tearing of a layer of asphalt. When it is a new driveway, it has to initially be excavated to make room for a layer of crushed stone of adequate depth. A geotextile membrane will be placed under the granular backfill if the soil proves to be somewhat loamy (clayey). If you have a new house, it is ideal to wait 6 to 12 months prior to paving your drive, to enable the dirt to settle naturally. In the case of a repair of this entry, an easy replacement of the asphalt layer can be considered if the contractor believes that the existing foundation is sufficient. In both scenarios, base redone or foundation maintained, the duration of its warranty must be exactly the same.

Tar And Chip Paving Pell City Alabama

The weather conditions in our beautiful province may have a disastrous impact in an asphalt drive, hence the significance of adding a slope having a minimum slope of 2%. This will enable water to drain into the road and decrease the risk of heaving or cracking. This significant detail has to be taken into consideration when excavating and preserved during backfilling.

In case you've got a van or recreational vehicle, notify the builder before the onset of the job: he is going to be able to supply materials accordingly. Some asphalt mixtures produce an asphalt which is more immune to heavy duty vehicles.

The asphalt layer should have a first thickness of 6.35 to 7.6 cm (2.5 to 3 in) in order to reach a thickness of 5 cm (2 in) after being compacted. For optimum stability, the base should extend over the surface to be paved by about thirty centimeters (a couple inches) on each side. Also note that the installation of unwanted supports around the foundation is a good method to prevent potential cracks and that asphalting done in cold weather will be of inferior quality. It's therefore better to wait for the bright days to return before starting work.

A Tar And Chip Paving contract with your contractor in Pell City

To avoid unpleasant surprises, then choose your contractor and make certain the name and address of the business are composed on the contract. The beginning and end dates of this job, in addition to evidence of this builder's liability insurance and also the technical details of the project to be carried out, should also be included. No contractor should require a down payment before work begins. To avoid the inconvenience that might cause unforeseen costs, take a look at the Tar And Chip PavingPell City site. You may thus have all the resources in hand to successfully finish your asphalt paving project.

Tar And Chip Paving Pell City - Greatest Alabama in Alabama!

For caliber asphalting work , call on Tar And Chip Paving, Pell City professional team. Confirm our Business department to find out the regions served.

Snow Removal Pell City | Asphalt Pell City
Home >> alabama/pell city >> tar and chip paving
Share this...