Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Options for the asphalt Coating in Fairbanks, Alaska


Tar And Chip Paving installed in an unstable surface can quickly lead to problems. There are three main options for the basic setup:

  1. Paving Over Existing Driveway: If your existing driveway is in good shape and not revealing severe cracks or crumbling, hot asphalt mixture can be laid directly over your driveway. One aspect is elevation: make certain fences, garage floors, and other structures aren't compromised by the higher level of the surface.
  2. Eliminate old driveway, peg to the floor: The present driveway is completely removed (or you may not have a driveway yet) and 4 to 6 inches of warm paving stone is placed directly on the ground.
  3. Remove the old driveway and secure it to a good surface. This is the preferred method. An aggregated stone floor partly replaces part of the hot asphalt mixture.

Our Services:

The best time to install Tar And Chip Paving in Fairbanks

The longer asphalt you work, the more leeway you might have. By way of example, at 40 F, the crews just have 16 minutes to work on 1 1/2 inch thick asphalt. As the asphalt depth increases by 3 inches, the workability time also increases: 46 minutes. In general, for thin asphalt applications (approximately 1.5 cm), you should wait until temperatures are 21 ° C or higher. Between 50 and 60 F, you'll need to speak to your contractor. The hot mix is ​​still practical during this period, however, the time is limited.

How much can an Tar And Chip Paving price in Fairbanks?

Take into account the weather vagaries of the climate when choosing the quality of asphalt. The significant temperature variations that we experience cause appreciable damage to asphalt perform.

In addition, it'll be good to tell the contractor if you have a recreational vehicle or a van. He might have to adapt the asphalt mixture in order to be more immune to the weight of heavy vehicles.

The Benefits of Tar And Chip Paving

  • Smooth finish;
  • non-slip
  • Simple to Keep
  • watertightness ensured
  • withstands the rigors of this Quebec climate very well (provided it has been set up optimally);
  • prevents the growth of moss;

It will cost you between $ 3 and $11 per square foot; the price varies depending on the characteristic of the asphalt used and the paving contractor.

For a sustainable Tar And Chip Paving

The life of an asphalt paver can be around 20 years, when the very best states are met. We're referring to a professional paving builder, a great grade of asphalt as well as also an optimal asphalt laying technique.


The durability of residential asphalt paving largely depends on the standard of the placing. Really, the significant causes of deformation or tearing of an asphalt coating are the absence of compaction and a thin foundation. On the other hand, the upkeep of the asphalt sidewalk is also a determining factor in its longevity. That is to say, you'll have to seal your driveway once in 10 decades, at a minimum, so as to keep its good condition.


We suggest that you notify your asphalting builder in case you choose to get your driveway asphalt in order to offer your property. It may not be necessary to pay top dollar for placing asphalt , in such a case.

Tar And Chip Paving placing: cost and contract

The choice of the asphalt laying contractor is essential. In order to not have unpleasant surprises, then you will have to choose it carefully.

Guarantee that the paving contractor has liability insurance. A visit to the web site of the Office for Consumer Protection (OPC) will allow you to confirm whether an entrepreneur has been the subject of complaints.

The following details should be included in the arrangement:

- date of start and end of the work;

- evidence of insurance;

- technical particulars;

- RBQ certification number.

You ought to be aware that a paving contractor can't demand you to make a deposit before work has begun. However, you should agree to the payment terms and make sure it is about the contract.

A solid foundation for Tar And Chip Paving- Fairbanks

Prior to estimating the asphalt driveway to your new home by a contractor, or obtaining some basic knowledge is vital to make sure the job is done. Know first that the lack of compaction and the inadequate depth of the base are the two main sources for the deformation or tearing of a layer of asphalt. If it's a new driveway, it must initially be excavated to make room for a coating of crushed stone of sufficient thickness. A geotextile membrane is going to be placed under the granular backfill if the dirt turns out to be very loamy (clayey). If you own a new home, it's best to wait for 6 to 12 months prior to paving your drive, to allow the dirt to settle naturally. In the event of a fix of the entrance, an easy replacement of the asphalt layer can be considered if the contractor considers that the present base is adequate. In both cases, foundation redone or foundation preserved, the duration of its guarantee has to be exactly the same.

Tar And Chip Paving Fairbanks Alaska

The weather conditions in our beautiful province may have a devastating effect in an asphalt driveway, hence the importance of including a slope with a minimum slope of 2%. This will allow water to drain into the road and decrease the danger of heaving or cracking. This significant detail has to be taken into account when excavating and preserved during backfilling.

In case you have a van or recreational vehicle, notify the builder prior to the start of the job: he is going to have the ability to provide materials accordingly. Some asphalt combinations produce an asphalt which is more resistant to heavy duty vehicles.

The asphalt coating should have an initial thickness of 6.35 to 7.6 cm (2.5 to 3 ) so as to reach a thickness of 5 cm (2 ) after being compacted. For optimal stability, the foundation should extend across the surface to be paved by roughly thirty centimeters (a couple inches) on each side. Also note that the setup of unwanted supports around the foundation is a good method to avoid potential cracks and that asphalting done in cold weather will be of poor quality. It is therefore better to await the sunny days to return before starting work.

A Tar And Chip Paving contract with your builder in Fairbanks

To avoid unpleasant surprises, then choose your contractor and be certain the name and address of the company are composed on the contract. The start and finish dates of this job, as well as evidence of this builder's liability insurance and the technical specifics of the project to be completed, should also be included. No contractor should require a deposit before work starts. To prevent the inconvenience that might cause unforeseen costs, visit the Tar And Chip PavingFairbanks website. You will thus have all the tools in hand to successfully complete your asphalt paving project.

Tar And Chip Paving Fairbanks - Greatest Alaska in Alaska!

For caliber asphalting work , phone on Tar And Chip Paving, Fairbanks professional team. Confirm our Business section to find out the regions served.

Snow Removal Fairbanks | Asphalt Fairbanks
Home >> alaska/fairbanks >> tar and chip paving
Share this...