Easy and Trusted Asphalt

Call Us Today: 1240.226.2848

Tar And Chip Paving- Alternatives for the asphalt surface in Juneau, Alaska


Tar And Chip Paving installed on an unstable surface could quickly lead to problems. There are three Chief choices for the basic installation:

  1. Paving Over Existing Driveway: If your current driveway is in good shape rather than showing serious fractures or crumbling, hot asphalt mixture can be placed directly within your driveway. 1 aspect is height: make certain fences, garage floors, and other constructions are not compromised by the greater level of the new surface.
  2. Remove old driveway, peg to the ground: The existing driveway is totally removed (or you might not have a driveway yet) and 4 to 6 inches of hot paving stone is placed directly on the ground.
  3. Eliminate the old driveway and secure it into a solid surface. This is the preferred method. An aggregated stone floor partly replaces part of this hot asphalt mixture.

Our Services:

The best time to install Tar And Chip Paving from Juneau

The longer asphalt you operate, the more leeway you might have. For instance, in 40 F, the crews only have 16 minutes to work on 1 1/2 inch thick asphalt. Generally, for lean asphalt programs (about 1.5 cm), you need to wait until temperatures are 21 ° C or even higher. Between 50 and 60 F, then you'll need to consult with your contractor. The hot mix is ​​still practical in this period, however, the time is constrained.

How much can an Tar And Chip Paving cost in Juneau?

Consider the weather vagaries of the climate when deciding upon the quality of asphalt. The significant temperature variations we experience cause considerable damage to asphalt perform.

Furthermore, it will be good to tell the contractor should you own a recreational vehicle or a van. He will have to adapt the asphalt mix so as to be more resistant to the burden of heavy vehicles.

The Benefits of Tar And Chip Paving

  • Smooth end;
  • non invasive
  • Simple to Keep
  • watertightness guaranteed
  • withstands the rigors of the Quebec climate quite well (provided it has been installed optimally);
  • prevents the growth of moss;

It'll cost you between $ 3 and $11 per square foot; the price fluctuates based on the characteristic of the asphalt employed and the paving contractor.

To get a sustainable Tar And Chip Paving

The life of an asphalt paver may be around 20 years, when the best states are met. We're talking about a professional paving builder, a great quality of asphalt and an optimal asphalt laying technique.

Tar And Chip Paving in Juneau: cost, quality of work and lifespan


The longevity of residential asphalt paving chiefly is dependent on the standard of the laying. Indeed, the major causes of deformation or ripping of an asphalt layer are the absence of compaction plus a lean base. However, the maintenance of the asphalt pavement is also a determining factor in its longevity. That is to say, you'll need to seal your drive once in ten decades, at a minimum, so as to maintain its good condition.


We suggest that you inform your asphalting builder if you choose to get your driveway asphalt in order to offer your property. It may not be essential to pay top dollar for laying asphalt , in this case.

Tar And Chip Paving placing: price and contract

The option of the asphalt laying builder is indispensable. In order to not have unpleasant surprises, you will have to choose it carefully.

Make sure the paving contractor has liability insurance coverage. A trip to the website of the Office for Consumer Protection (OPC) will make it possible for you to verify whether an entrepreneur has become the subject of complaints.

The following details should be included in the contract:

- date of beginning and finish of the job;

- proof of insurance;

- technical details;

- RBQ certification number.

You ought to be aware that a paving contractor can't require that you make a deposit before work has started. But you need to agree to the payment terms and be sure it's on the contract.

Before redoing the asphalt drive to your new home by a builder, or obtaining some fundamental knowledge is imperative to guarantee that the job is done. Know first that the lack of compaction and the insufficient thickness of the base are the two chief causes of the deformation or tearing of a coating of asphalt. If it is a new driveway, then it must first be excavated to make room for a layer of crushed stone of sufficient thickness. A geotextile membrane will be set under the granular backfill if the soil proves to be very loamy (clayey). If you have a new house, it is best to wait 6 to 12 months before paving your driveway, to allow the soil to settle naturally. In the event of a repair of the entry, a simple replacement of the asphalt coating can be considered if the contractor considers that the present foundation is adequate. In both cases, foundation redone or base maintained, the duration of its guarantee has to be the same.

Tar And Chip Paving Juneau Alaska

The weather conditions in our lovely state may have a disastrous impact on an asphalt driveway, hence the significance of adding a slope having a minimum slope of 2%. This will allow water to drain into the street and minimize the danger of heaving or cracking. This significant detail must be taken into consideration when excavating and preserved during backfilling.

If you have a van or recreational vehicle, notify the builder prior to the onset of the work: he is going to have the ability to provide materials so. Some asphalt mixtures produce an asphalt which is more resistant to heavy-duty vehicles.

The asphalt coating should have a first thickness of 6.35 to 7.6 cm (2.5 to 3 in) in order to accomplish a thickness of at least 5 cm (2 ) after being compacted. For optimum stability, the base should extend over the surface to be paved by roughly thirty centimeters (a couple inches) on each side. Also note that the installation of unwanted supports around the base is a fantastic way to avoid possible cracks and that asphalting done in cold weather is going to be of inferior quality. It's therefore better to wait for the sunny days to return before starting work.

A Tar And Chip Paving contract with your contractor in Juneau

To avoid unpleasant surprises, then choose your contractor diligently and be sure the title and address of his business are composed on the contract. The beginning and end dates of the work, as well as proof of the contractor's liability insurance and also the technical specifics of this job to be carried out, should also be included. No contractor should require a down payment before work starts. To prevent the inconvenience that could lead to unforeseen expenses, take a look at the Tar And Chip PavingJuneau site. You will thus have the resources in hand to successfully complete your asphalt paving project.

Tar And Chip Paving Juneau - Greatest Alaska in Alaska!

For quality asphalting perform , call on Tar And Chip Paving, Juneau professional team. We've got more than twenty decades of experience in asphalt laying, resurfacing, maintenance and repair. Confirm our Business section to find out the regions served.

Snow Removal Juneau | Asphalt Juneau
Home >> alaska/juneau >> tar and chip paving
Share this...